How To: Activate Active Park Assist on Mustang Mach-E

[Piolin]

Thanks for the reply.

Unfortunately I tried that as well yesterday, didn't work. SOBDMC has 1 block only so both Write and Write all didn't do any difference, in fact I always do just Write one block instead of Write all.

I tried deleting the DTC, rebooting, and even a self-test procedure just in case, but it didn't help, just rejects any attempt to modify 7E6-01-01, it goes to 100%, waits for a bit then says "Writing block 1 failed" and "Access denied".

Note that all other modules were programmed successfully. I tried also to program in KEY ON ENGINE OFF mode (accessory mode), but that didn't work either. As an experiment I tried to modify 7E6-01-02, to a different value, strangely that worked, but 7E6-01-01 is just plain rejected.

Works properly APA?

Sponsored

 

[Piolin]

Finally, What DTC show in SOBDMC?

 

[Piolin]

I fitted 7E6-01-01 x3xx xxxx

 

[xwtk]

Works properly APA?

APA doesn't work, IPC throws an error gong, APA interface doesn't launch on APIM. Note that this is after driving for a few minutes so the side sensors get calibrated properly.

Right now side sensors are working properly, but APA doesn't launch.

SOBDMC DTC shows Invalid data received from Parking Assist Module A (Configuration mismatch). Any attempt to modify 7E6-01-01 to anything at all just fails.

 

[Piolin]

APA doesn't work, IPC throws an error gong, APA interface doesn't launch on APIM. Note that this is after driving for a few minutes so the side sensors get calibrated properly.

Right now side sensors are working properly, but APA doesn't launch.

SOBDMC DTC shows Invalid data received from Parking Assist Module A (Configuration mismatch). Any attempt to modify 7E6-01-01 to anything at all just fails.

But does the "park assist" button appear on the SYNC screen?

If you press this button (assuming it appears), does the image of the cars appear so you can choose how to park: parallel, perpendicular, or pull out?

Let us know.

Regards

 

[xwtk]

But does the "park assist" button appear on the SYNC screen?

If you press this button (assuming it appears), does the image of the cars appear so you can choose how to park: parallel, perpendicular, or pull out?

Let us know.

Regards

Yes the Park Assist button does appear on APIM (SYNC) as all the modules except SOBDMC were programmed successfully. But when clicking on it, it doesn't launch the Active Park Assist interface where you choose the parking mode. And when pressing the Park button on the center console an error sound is played by the instrument cluster (IPC).

 

[Piolin]

Yes the Park Assist button does appear on APIM (SYNC) as all the modules except SOBDMC were programmed successfully. But when clicking on it, it doesn't launch the Active Park Assist interface where you choose the parking mode. And when pressing the Park button on the center console an error sound is played by the instrument cluster (IPC).

Please, photo or video.

 

[Dynamo]

Thanks for the reply.

Unfortunately I tried that as well yesterday, didn't work. SOBDMC has 1 block only so both Write and Write all didn't do any difference, in fact I always do just Write one block instead of Write all.

I tried deleting the DTC, rebooting, and even a self-test procedure just in case, but it didn't help, just rejects any attempt to modify 7E6-01-01, it goes to 100%, waits for a bit then says "Writing block 1 failed" and "Access denied".

Note that all other modules were programmed successfully. I tried also to program in KEY ON ENGINE OFF mode (accessory mode), but that didn't work either. As an experiment I tried to modify 7E6-01-02, to a different value, strangely that worked, but 7E6-01-01 is just plain rejected.

Hello, seems that some issues with forscan or that this block under the protection since 2024. I have something like that, but with HCM calibration, you can write to support team, give them logs and describe situation (you can tell only, that you can edit parameters in SOBDMC). The will try to help, how to provide debug info
http://forscan.org/contactus.html#debug_info

 

[xwtk]

Please, photo or video.

Unfortunately can't do at this moment as the car is not in my possession. I am more than sure the cause is the SOBDMC and I was wondering if anyone has any ideas on why it rejects the programming, maybe another value must be set for 2024 and onwards models?

 

[xwtk]

Hello, seems that some issues with forscan or that this block under the protection since 2024. I have something like that, but with HCM calibration, you can write to support team, give them logs and describe situation (you can tell only, that you can edit parameters in SOBDMC). The will try to help, how to provide debug info
http://forscan.org/contactus.html#debug_info

Thanks a lot, I will make sure to contact them to find a solution! Just to note that I was able to successfully activate APA on 2022MY and 2023MY Mach-Es properly, only with this one I have an issue with SOBDMC.

 

[Blucooper03]

Sounds like I need to bump into someone in the LA area with Forscan to enable this in our 2nd vehicle. We have a 21 and 22.

 

[xwtk]

Sounds like I need to bump into someone in the LA area with Forscan to enable this in our 2nd vehicle. We have a 21 and 22.

Go ahead, I will say the parallel parking is very good, really surprised on how good it actually works.

 

[w0ger]

SOBDMC
7E6-01-01 x3xx xxxx xx

IPMA
706-01-01 xxxx x2xx xx--
706-02-01 xx73 xxxx xx--
706-02-01 xxxx xxxx 8x--
706-12-01 xxBC xxxx xx--
706-13-01 xxCx xxxx xx--

IPC
720-01-01 xxxx xxxx x4--

APIM
7D0-08-01 Exxx xxxx xx--
7D0-08-01 xxxx xxxB xx--

PSCM
730-03-01 xxFF xxxx xx--

I followed the steps here, but when updating thee PSCM I get an error message in ForScan v2.3.55.release:

Gain security access failed - security key is wrong
Service procedure has been interrupted

I noticed in another thread, the solution for this was to upgrade the version of ForScan.

When I attempted to upgrade to ForScan v2.3.68 - Windows classified it as malware and prevented the installation.

@Dynamo I noticed you have ForScan v2.4.19 beta. Could you send me a DM with the link to that?

Any other ideas?

 

[xwtk]

I followed the steps here, but when updating thee PSCM I get an error message in ForScan v2.3.55.release:

Gain security access failed - security key is wrong
Service procedure has been interrupted

I noticed in another thread, the solution for this was to upgrade the version of ForScan.

When I attempted to upgrade to ForScan v2.3.68 - Windows classified it as malware and prevented the installation.

@Dynamo I noticed you have ForScan v2.4.19 beta. Could you send me a DM with the link to that?

Any other ideas?

Windows did the same for me today, just add FORScan folder to the exclusions list.

 

[Dynamo]

I followed the steps here, but when updating thee PSCM I get an error message in ForScan v2.3.55.release:

Gain security access failed - security key is wrong
Service procedure has been interrupted

I noticed in another thread, the solution for this was to upgrade the version of ForScan.

When I attempted to upgrade to ForScan v2.3.68 - Windows classified it as malware and prevented the installation.

@Dynamo I noticed you have ForScan v2.4.19 beta. Could you send me a DM with the link to that?

Any other ideas?

Sure, I'll send it
About first question - I agree that your version is outdated and you need try newer. About malware - very strange, because I never seen issue with Forscan, I used only official links for download. Which windows on your laptop and do you have installed any 3rd party antiviruse soft?
And after you uodate the software, remove old profiles of your vehicle and start scanning car from scratch

Sponsored