Power-Up 6.7.0

[JohnFoxeSheets]

That was the 6.2.1 update? If so yes. I received 6.6.0 then 6.2.1 and today 6.7.0

Interesting. Thank you.

Sponsored

 

[kennelh]

That was the 6.2.1 update? If so yes. I received 6.6.0 then 6.2.1 and today 6.7.0

I could be wrong, but I think 6.2.1 was the APIM update.

 

[Gullwingdmc]

Wait, has @Jimrpa really not commented yet?

 

[machme]

That was the 6.2.1 update? If so yes. I received 6.6.0 then 6.2.1 and today 6.7.0

Let me double check that OTA order later tonight through PTS. I stopped receiving the notifications consistently in FP as few weeks ago

I could be wrong, but I think 6.2.1 was the APIM update.

Not sure, I lost track with all recent updates. Let me try to get a OTA dashboard view to share later tonight.

 

[machme]

When I select the OTA dashboard the page never loads. Not sure if others are seeing this.

 

[blkadr08]

Can we job 1’s get anywhere near that update? Still on 6.1.0 here.

Still on 6.1.0 also. For two years, I have been behind the curve with the inconsistent and spotty rollout of OTA updates. Wont Be buying another of these otherwise good cars.

 

[elmedico27]

I could be wrong, but I think 6.2.1 was the APIM update.

That’s correct

 

[noflipping]

How is it possible I can do this... but I only have 4.2.1 and still can't control the heat with the volume control???

 

[JeffGo]

Still on 6.1.0 (MY 21 Job 1), but I've had the frunk functions (screen, door pillar) for about a year now and the FP remote more recently.

 

[HuntingPudel]

How is it possible I can do this... but I only have 4.2.1 and still can't control the heat with the volume control???

Is your car a really early 2021, or is it a Job2 car? Only the Job1 cars do not have the proper software to pop the frunk lid. Ford has been slow rolling out an update so many people have manually updated their BCM and GFM software in order to make the actuator work. From there, it's been either a FORscan session to enable the center screen button or a newer routine in FDRS to activate the same button, then waiting for Ford to update its back-end servers so that the button appears in FordPass for the specific VIN. Now it looks like they packaged all of that into an OTA. Three years aftewr the Job1 cars started rolling off the assembly line. ??

 

[TallNate]

Is my 2021 "First Edition" the same as a Job 1 car?

 

[kennelh]

Is my 2021 "First Edition" the same as a Job 1 car?

Yes

 

[milepost1]

Yes, you won't get updates installed if your car is parked. Strongly recommend driving it minimum 30 minutes per week. However if Ford hasn't made updates available to you yet, they can't install no matter what you do.

Are you sure? Wrecked my 22. Was at lot for 3 months b4 they totaled. Recieved notice of a couple updates. Pretty sure they didn't drive it as had to use fork lift to bring it to front for me to get my stuff.

 

[SONEWBE]

In September, I received multiple updates in one week without driving the car. I just received notification of the updates in ford pass. I also received the ability to open the frunk via ford pass in one of those updates. The dealer did update a couple of modules in August. I still don’t have the frunk button on the sync screen. My car is a 2021 job 1.

 

[HuntingPudel]

Is my 2021 "First Edition" the same as a Job 1 car?

All First Editon MMEs were produced during the 2021 Job1 timeframe, so it is a 2021 Job1 car, but not all ‘21 Job1 cars are First Editions. ??

Sponsored