Replacement clips for frunk panels- Source?

[Maquis]

I seem to recall some previous posts about the square-headed clips that hold the interior frunk panels in place, but I can't find what I'm looking for. IIRC, the clips aren't available from Ford - you have to buy the whole panel(s), but I thought someone posted a source for these clips in the aftermarket. any advice is appreciated.

Thanks!

Sponsored

 

[HuntingPudel]

These are the ones that fall out all the time. They’re sold in a 4 pack by Ford. I keep some in my glove box just in case. ??

@MyLittlePony2022 sourced these and a lot of other generic versions of panel clips in bulk. Maybe William can chime in on his sources. ??

 

[MyLittlePony2022]

I have not found the frunk trim clips in bulk, so have to order them online from the dealer Once you know the FoMoCo part number, you can do a search and find the dealer with the lowest cost and shipping. I have found that some online dealers sell for a great price but make up for it with shipping and vise versa. I have found it at Tasca parts but their shipping is too high.

I put some tape on the trim piece to try to hold the clips in place. I am going to add LED lights to my frunk after seeing @HuntingPudel lights. I will see if what I did works. There were some other posts out there on ways to wire them in place.

I did find the orange interior trim clips (W718230-S300) and the white door clips (W713297-S300)
Amazon in bulk. I try to search there and other online sources to see if I can get them in bulk and cheaper than at the dealer. I put the FoMoCo part numbers so other can find them in a search.

 

[HuntingPudel]

<SNIP>
I put the FoMoCo part numbers so other can find them in a search.

The machinist I used to use when I was building TRD engines was a decidedly C#@vy guy. He always called ‘em “MoFoNoGoNoMo” instead of FoMoCo. He was fascinated by the Toyota tech I was playing with and tolerant of my “Pony-Yak” stuff. ??

 

[Henk]

When you have access to a 3D Printer you can print them yourself:
https://www.printables.com/model/862288-mustang-mach-e-front-trunk-area-clip/files
Do use a good filament at least PETG or better for temperature.

They printed fine on my Prusa MK4S printer (with supports). Though I have not yet tested the fit in my MachE.

 

[rolltide]

Are these the correct clips that secure the trim pieces go around the frunk and cover the 12v battery?

https://www.ford.com/product/locking-pin-p4000113356

https://ford.oempartsonline.com/oem-parts/ford-fender-ledge-cover-pin-w720957s300

https://www.fordpartspros.com/oem-parts/ford-fender-ledge-cover-pin-w720957s300

 

[Teslaeata]

When you have access to a 3D Printer you can print them yourself:
https://www.printables.com/model/862288-mustang-mach-e-front-trunk-area-clip/files
Do use a good filament at least PETG or better for temperature.

They printed fine on my Prusa MK4S printer (with supports). Though I have not yet tested the fit in my MachE.

Whoah! Very many thanks for this link to printable clips.

I’ll give that a whirl.

However my dealer, Perrys Ford of Mansfield clearly used a new clip when they worked on my car last and left the new unused left over clips in my glove box, didn’t charge me for them which I thought was really kind of them.

One happy customer

 

[Teslaeata]

When you have access to a 3D Printer you can print them yourself:
https://www.printables.com/model/862288-mustang-mach-e-front-trunk-area-clip/files
Do use a good filament at least PETG or better for temperature.

They printed fine on my Prusa MK4S printer (with supports). Though I have not yet tested the fit in my MachE.

Do you know of a printable boot board support, please?

 

[markboris]

Are these the correct clips that secure the trim pieces go around the frunk and cover the 12v battery?

https://www.ford.com/product/locking-pin-p4000113356

https://ford.oempartsonline.com/oem-parts/ford-fender-ledge-cover-pin-w720957s300

https://www.fordpartspros.com/oem-parts/ford-fender-ledge-cover-pin-w720957s300

Yes they all are.

 

[MoonRiver]

Try these. I bought a bunch in the past they fitted well. Not sure if they redesigned it but it costs almost nothing. So give it a shot.
https://share.temu.com/3cirWCOMzqC

Sponsored