Post here if you have an active FDRS account and are willing to look up info for others

[rugedraw]

^^^ Hmm looks like camera module rear is new.

Many people on the ICE forums have reported issues with faults being reported in relation to driver assist features after 6.13.0 or updating the CMR with FDRS. A few people have hypothesized that this CMR is to correct that issue, but I do not know that for sure yet.

Can someone check mine as well?
3FMTK4SE2PMA02567

The mothership loves you. You even got the new APIM update that gives you AM radio.

Modules still pending updates are below. If you get that CMR update showing down there via OTA, please let me know so I can check the details on it.

Sponsored

 

[YellowItsMe]

Hi, can someone check my car please?
3FMTK4SX1MME03797

Thanks!

 

[FastEV]

Modules still pending updates are below. If you get that CMR update showing down there via OTA, please let me know so I can check the details on it.

Details on my CMR version update this past weekend...

In my 2023 GTPE I received the dreaded 6.13.0 OTA update a couple of weeks ago which broke the CMR, which broke BlueCruise. I think the 6.13.0 OTA update pushed CMR version MB6T-3G604-CD. When looking in FDRS, here's the DTC I saw for the CMR module, the same as others have reported with SSM-52214:

When looking in FDRS I was hopeful a fix was available as I had a CMR update pending, along with a few others:

I successfully applied most of the other updates but the CMR update did not apply cleanly, I tried a couple of times with the same result. It appears the newer CMR was version MB6T-3G604-NE:

After the unsuccessful programming attempt, I now have a purple "Responded Negatively" status for the CMR module which still shows the original broken version which came in via the OTA a few weeks ago, MB6T-3G604-CD:

I'm hopeful that when Ford pushes the promised March OTA to fix the CMR that it will automatically load the new version and resolve the issue. Otherwise I may need to try another manual update via FDRS once the new software version is available. Hopefully this won't require a dealer visit as the module appears to still be online since it tries to apply the new software but fails to fully reprogram after about an hour of progressing through the various software loading steps.

If anyone sees a CMR version newer than MB6T-3G604-NE show up over the next few weeks, please let everyone know as hopefully that will be the version which resolves the CMR issue for BlueCruise. Likewise, if anyone is able to successfully load version MB6T-3G604-NE and knows any special FDRS procedures or other words of wisdom, please share.

 

[rugedraw]

If anyone sees a CMR version newer than MB6T-3G604-NE show up over the next few weeks, please let everyone know as hopefully that will be the version which resolves the CMR issue for BlueCruise. Likewise, if anyone is able to successfully load version MB6T-3G604-NE and knows any special FDRS procedures or other words of wisdom, please share.

Thanks for the detailed response. This issue has affected many owners across different vehicle platforms. I have lucky and only gotten a pair of "pre-collision assist not available" warnings, but everything works fine.

You seem to know what you're doing, but I did not see in your post any mention of you trying to clear the DTC's on the CMR before trying to update it. Did you try to clear the codes in the CMR before updating it?

 

[ILikeTurtles]

Hi! Can you please check my car for updates?

3FMTK3SUXNMA03920

 

[em5quare]

Hi, can you check my car for updates? Specifically, since I got 6.7.0, I'd like to know if the BCCM was updated - CSP 23B50 (supposedly 6.6.0 takes care of that). Thanks!

3FMTK3R77MMA62244

 

[rugedraw]

Hi! Can you please check my car for updates?

3FMTK3SUXNMA03920

Last OTA that was sent to you was 6.8.0 back in early September. It failed with error code:

"groupId":"1""errorCode":"InvalidAssemblyVbf(12)""errorCategory":"SwumEr(12)""ecuId":"1824"

I am not sure what that means, but nothing has been sent to you since then. Modules pending updates are below:

Hi, can you check my car for updates? Specifically, since I got 6.7.0, I'd like to know if the BCCM was updated - CSP 23B50 (supposedly 6.6.0 takes care of that). Thanks!

3FMTK3R77MMA62244

You got 6.6.0 four days before 6.7.0 which includes the BECM update. The modules updated in that update were:

 

[em5quare]

Last OTA that was sent to you was 6.8.0 back in early September. It failed with error code:

"groupId":"1""errorCode":"InvalidAssemblyVbf(12)""errorCategory":"SwumEr(12)""ecuId":"1824"

I am not sure what that means, but nothing has been sent to you since then. Modules pending updates are below:

You got 6.6.0 four days before 6.7.0 which includes the BECM update. The modules update

Last OTA that was sent to you was 6.8.0 back in early September. It failed with error code:

"groupId":"1""errorCode":"InvalidAssemblyVbf(12)""errorCategory":"SwumEr(12)""ecuId":"1824"

I am not sure what that means, but nothing has been sent to you since then. Modules pending updates are below:

You got 6.6.0 four days before 6.7.0 which includes the BECM update. The modules updated in that update were:

Thanks!

 

[bdesatnik]

Hi, can someone please check my car for updates? Thank you!!

3FMTK3SU6MMA09079

 

[FastEV]

You seem to know what you're doing, but I did not see in your post any mention of you trying to clear the DTC's on the CMR before trying to update it. Did you try to clear the codes in the CMR before updating it?

Thanks for the suggestion. I tried clearing the DTCs on all modules prior to each programming attempt. All of the other DTCs cleared but each time the CMR module came back with the purple "Responded Negatively" status and would not clear the DTC.

I didn't see (or possibly overlooked) any other diagnostic tools in FDRS to reset/configure the CMR as there are with other modules.

I'm still holding out hope that the upcoming March CMR update will resolve my issue, either automatically via OTA or manual FDRS update.

Were you able to find any additional details on the MB6T-3G604-NE version of the CMR software?

 

[CarGuy11]

^^^Geez let's hope OTA's start rolling again before March!

 

[rugedraw]

Thanks for the suggestion. I tried clearing the DTCs on all modules prior to each programming attempt. All of the other DTCs cleared but each time the CMR module came back with the purple "Responded Negatively" status and would not clear the DTC.

I didn't see (or possibly overlooked) any other diagnostic tools in FDRS to reset/configure the CMR as there are with other modules.

I'm still holding out hope that the upcoming March CMR update will resolve my issue, either automatically via OTA or manual FDRS update.

Were you able to find any additional details on the MB6T-3G604-NE version of the CMR software?

The only other thing I can think of is to PMI the CMR and when it asks if it is the original module, select "no".

No, nothing yet as far as details on the new CMR update. I'm not showing it for my truck yet. My BC works, but I have gotten a few sporadic "pre-collision not available" alerts on my dash that don't report any codes to the cloud. I'm also reporting codes in my CMR and IPMA that I can't clear out. On the TSB's listed next to the CMR code suggest a possible faulty coaxial cable, but I doubt that's it since the problem issues started after I performed the update in December.

 

[sean7512]

Could someone check the status and pending updates for my 2 VINs (both are 2023.0)?

This one has gotten a lot of updates in a row (6 in about 2 weeks or so).
3FMTK4SE4PMA46070

This one is STILL stuck at Not Complete 6.3.0 since Dec 5, curious if the trigger to try again was ever sent back out or what the heck is going on.
3FMTK4SE6PMA45941

 

[zvez]

I'm told that some new updates have dropped into the FDRS which may resolve my charging issue that I've been going back and forth with ford for five months now.
Could someone run this vin please (I know I got one earlier but want to see if new uploads are there)
Thanks Vin 3FMTK4SX5PMA80214

 

[rugedraw]

Could someone check the status and pending updates for my 2 VINs (both are 2023.0)?

This one has gotten a lot of updates in a row (6 in about 2 weeks or so).
3FMTK4SE4PMA46070

This one is STILL stuck at Not Complete 6.3.0 since Dec 5, curious if the trigger to try again was ever sent back out or what the heck is going on.
3FMTK4SE6PMA45941

First VIN has a very extensive and healthy OTA history. In terms of power-up updates, it seems to only be missing 6.13.0.

Second VIN has had 6.3.0 fail twice due to software mismatch issues. The files the server wants to send to it didn't match the manifest and the update failed. It happens quite often. Nothing you can do but wait for another OTA trigger to be created for that vehicle and hope the correct files are sent out next time.

@FastEV I asked for a second opinion on your case. Purple indicates a potentially bricked module. The PMI I recommended is the correct approach.

Sponsored