Post here if you have an active FDRS account and are willing to look up info for others

[Mike G]

Can I get a check? Received OTA ECG-24.2.5.61 the other day. Thx! 3FMTK3SU9NMA41574

Sponsored

 

[BenW1976]

Would someone please check my vin?

3FMTK3RMXMMA49316

TIA

 

[kennelh]

Would someone please check my vin?

3FMTK3RMXMMA49316

TIA

And mIne... Thanks!

3FMTK3R75MMA09929

 

[DylanBeast]

Could someone look into mine, recently replaced damaged sodcmc with a used one and think it might need firmware update to function
VIN
3FMTK3SU3NMA11423
Thanks in advance

 

[Mike G]

Would someone please check my vin?

3FMTK3RMXMMA49316

TIA

You have no updates showing as available in FDRS this morning.

 

[Mike G]

And mIne... Thanks!

3FMTK3R75MMA09929

 

[Mike G]

Could someone look into mine, recently replaced damaged sodcmc with a used one and think it might need firmware update to function
VIN
3FMTK3SU3NMA11423
Thanks in advance

No powertrain updates at all for this VIN......but...if you have replaced a module and got it from a completely different vehicle then you may have to do a 'VIN write procedure' on the replacement module using FDRS, and then just to be safe I'd do a PMI on the SOBDMC to ensure that it was properly recognized and had the correct software installed.

 

[DylanBeast]

No powertrain updates at all for this VIN......but...if you have replaced a module and got it from a completely different vehicle then you may have to do a 'VIN write procedure' on the replacement module using FDRS, and then just to be safe I'd do a PMI on the SOBDMC to ensure that it was properly recognized and had the correct software installed.

Not your fault at all, all of the modules starting with SO look the same, but i was referring to the Side Obstacle Detection Control Module C. Would those recommendations still aply? I wrote mt as built in forscan and performed the CCM calibration but it continues showing horizontal alignment error. Everthing seems okay mounting wise(old module just barely cracked in low speed accident)

 

[kiowa1021]

Would someone be able to check my VIN? It's been a few months since my last FDRS session, and I'm hoping that there are some updates that will get me closer to 6.14. Thank you!

3FMTK3SU1MMA25917

 

[Mike G]

Not your fault at all, all of the modules starting with SO look the same, but i was referring to the Side Obstacle Detection Control Module C. Would those recommendations still aply? I wrote mt as built in forscan and performed the CCM calibration but it continues showing horizontal alignment error. Everthing seems okay mounting wise(old module just barely cracked in low speed accident)

Ah my bad, I thought it was a typo ?

All of your side obstacle modules have the same "J" rev. software installed currently.

 

[Mike G]

Would someone be able to check my VIN? It's been a few months since my last FDRS session, and I'm hoping that there are some updates that will get me closer to 6.14. Thank you!

3FMTK3SU1MMA25917

 

[DylanBeast]

Ah my bad, I thought it was a typo ?

All of your side obstacle modules have the same "J" rev. software installed currently.

Strange, when i check my strategy version on forscan its showing this. Can i do the pmi using a simple obdlink ex on fdrs or is that something that requires a passthrough device

 

[Mike G]

Strange, when i check my strategy version on forscan its showing this. Can i do the pmi using a simple obdlink ex on fdrs or is that something that requires a passthrough device

Will require a J2534 adapter and FDRS AFAIK.

Where would you get the appropriate files to do the PMI if not from FDRS?

 

[Ajax]

Any failed updates for VIN 3FMTK3SU1MMA39848? Had 30k service back in July and replaced 12V voluntarily. I think the last update I got was 24-PU0301-BLM-PE in June 2024.

 

[mh58]

Please check this VIN - 3FMTK3SU4MMA31081

Thanks!

Sponsored